Micro CLT cabins, made in Latvia. A ready-made sauna line for resellers and installers, shipped flat-packed worldwide.
A finished sauna pod arrives on a lorry and needs a crane, a clear driveway and a lot of luck. Ours arrives as six panels. They are carried by hand, one at a time, through a standard side gate, up to a roof terrace, or down to a lakeside plot with no vehicle access at all.
Two to four people, forty minutes to two hours, ordinary hand tools. No crane, no foundation, no trades.
Compact enough for a courtyard, a roof terrace, or a garden with side-gate access only.
The family size. Two-tier benching with room to lie back on the upper bench.
Full size, for entertaining and for commercial settings — gyms, spas, holiday lets.
Every model is available in Base or Premium. The structure is identical; the interior is not.
The Base shares its entire structure with the Premium. The same micro CLT shell, the same 8 mm toughened glazing, the same sealed flat roof, the same stainless fixings. What changes is the lining: solid aspen benches sit against the panel face, and the money goes into the build rather than the finish.
Thermo-treating bakes the moisture out of aspen. What comes back is timber that will not warp or split, that stays cool to the touch at ninety degrees, and that has darkened all the way through to a deep honey. In the Premium it lines the entire cabin: walls, ceiling, benches and vents, not only the boards you sit on.
Premium is the same cabin with a thermo-aspen interior throughout. Most customers choose it once they have seen both.
LED strip runs on 6 × 18650 rechargeable batteries, not supplied. Heaters are quoted separately.
| Model | Width | Height | Seats | Floor area |
|---|---|---|---|---|
| ROYAL S | 1304 mm | 2028 mm | 2 | 2.08 m² |
| ROYAL M | 2050 mm | 2028 mm | 4 | 3.20 m² |
| ROYAL L | 2500 mm | 2025 mm | 6 | 4.00 m² |
Every material in the cabin carries a manufacturer declaration. We can supply the paperwork with the order, which is more than most garden sauna suppliers can do.
EN 13986 · E1 formaldehyde · λ 0.13 W/mK
EN 12150-2 · 200 K thermal shock · Rw 33 dB
EN 1504-2 · fully sealed
M1 emission class
We can supply and ship a heater specified to the cabin size, quoted separately.
Already partnered with a heater brand? We ship the cabin pre-cut with the electrical penetration, ready for your own unit to be fitted on site.
Wall panels, bench boards and barrel sauna materials in five resin-free species, shipped weekly worldwide.
Minimum to open an account is ten units, which you can mix across sizes and finishes however suits your market. You buy at trade, set your own retail. We ship from Riga to your premises or direct to your customer, with freight and customs handled. We work with one partner per territory.
Two to four people, forty minutes to two hours, using ordinary hand tools — a 15 mm wrench, an impact driver with Torx bits, a rubber mallet, a level and a silicone gun. A full illustrated manual is included.
Almost certainly. The cabin arrives as six separate panels, carried by hand rather than craned in. This is the main reason customers choose it over a fully assembled pod. Send us a photograph of the access and we will confirm.
A level, load-bearing base — paving slabs or bricks are ideal. The support points must line up with the cabin's pegs. Getting the base right is the single most important part of the installation; an out-of-level base shows in every panel joint and the door will not close evenly.
No. We can supply one specified to the cabin size, quoted separately. If you already work with a heater brand, we ship the cabin pre-cut with the electrical penetration so your own unit can be fitted on site.
Yes. Electrical installation must be carried out by a certified electrician. In the UK this is notifiable work under Part P.
The structure is identical — same shell, glazing, roof and fixings. Base has solid aspen bench seating against the panel face. Premium lines the entire cabin in thermo-aspen: walls, ceiling, benches and vents.
Freight from Riga, with export and import declarations handled, door to door. Delivery is quoted per destination.
The CLT panels are NOVATOP SWP to EN 13986 with E1 formaldehyde classification. Glazing is 8 mm toughened to EN 12150-2. The roof membrane is EN 1504-2. Interior finishes are Teknos M1 emission class. We can supply the declarations with your order.
Contact us to arrange a viewing or a sample of the cladding and interior timber.
Tell us your market and we will send trade pricing, brochures and terms. Minimum order to open an account is ten units, mixed across the range. One partner per territory.